CONFAST LDC384 3/8" x 4" Zinc Plated Large Diameter Concrete Screw for Anchoring to Masonry, Brick or Block (25 per Box)
Produktdetails
| Artikelnummer | 223922461 | Erscheinungsdatum | 2026/05/09 | Listenpreis | €14.45 | Modellnummer | 223922461 | ||
|---|---|---|---|---|---|---|---|---|---|
| Kategorie | |||||||||
ApplicationsThe anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete, Brick or Block.EnvironmentThe anchor is designed for use in a Dry environment.Head Style The anchor is a Hex Washer Serrated head and is designed to allow the head to sit on top of the surface of the item being attached.Hole Diameter/Bit DiameterThe anchor requires a 3/8" hole to be drilled in the base material (Concrete). The hole should be drilled with carbide tipped bit using a hammer drill.Driver RequiredA 9/16" nut driver is required for driving the anchor into the base material.Diameter of Anchor The diameter of the anchor is 3/8".Length Anchor The length of the anchor is 4"Minimum EmbedmentThe minimum anchor embedment into the concrete is 1-1/2". Therefore, the anchor must be installed so that a minimum of 1-1/2" of the anchor is embedded into the concrete.Maximum Fixture ThicknessThe maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 2-1/2". This will ensure that the minimum embedment of 1-1/2" will be met.Fixture Hole DiameterTo fasten an object using these anchors, the hole in the object must be at least 7/16" to accomodate the 3/8" anchor. If the hole is not at least 7/16" the anchor will not fit through.Spacing between AnchorsEach anchor must be spaced a minimum distance of 6" from each other when measured center to center.Edge DistanceIt is very important not to install the anchor any closer than 3" from an unsupported edge of the concrete.
- WILL CUT ITS OWN THREAD INTO CONCRETE - When inserted in to properly drilled hole
- WILL CUT ITS OWN THREAD INTO CONCRETE - When inserted in to properly drilled hole
- LOW TORQUE THREADS - easy installation
- SERRATED HEX WASHER HEAD - Prevents back-out
- SINGLE PIECE DESIGN - No assembly required; ready to install
- USE A ANSI STANDARD CONCRETE BIT - 3/8" bit, size is the same as the anchor diameter
| UPC | 820274006016 |
|---|---|
| ASIN | B084N8W9DC |
| Brand | CONFAST |
| Head Type | Hex |
| Size Name | 4" |
| Metal Type | Carbon Steel, Zinc |
| Unit Count | 30 Count |
| Item Weight | 16 ounces |
| Part Number | LDC384 |
| Thread Size | 3/8 inch |
| Thread Type | Self-tapping |
| Drive System | External Hex |
| Finish Types | Zinc Plated |
| Manufacturer | CONFAST |
| Thread Class | Concrete Screw |
| Thread Style | Concrete Screw |
| Fastener Size | 3/8 in x 4 in |
| Fastener Type | Screw |
| Item Diameter | 0.38 Inches |
| Material Type | Case Hardened Carbon Steel, Zinc Plated |
| Exterior Finish | Zinc,Steel |
| Thread Coverage | Partially Threaded |
| Number of Pieces | 30 |
| Screw Head Style | Hex |
| Screw Point Style | Hex Washer Serrated |
| Set Screw Thread Type | Low Torque Threads |
| Compatible Groove Diameter | 0.38 Inches |
Korrektur der Produktinformationen
Wenn Sie Unvollständigkeiten oder Fehler in den Produktinformationen auf dieser Seite bemerken, nutzen Sie bitte das Korrekturformular unten.
KorrekturanfrageKundenbewertungen
Für dieses Produkt liegen derzeit keine schriftlichen Bewertungen vor.