1pc ZS-X11F V3 DC 6.5 -50V Three-Phrase Brushless Motor Control Board BLDC Driver Regulator 380W PWM Signal Duty Cycle

Stepper Motor DriverDC 6.5 -50V Three-Phrase Brushless DC Motor Control Board BLDC Motor Driver Regulator 380W PWM Signal Duty CycleSignal input description:1. The connection of the V/P short contact means that the PWM signal input effectively recognizes the real PMW signal to support the 3.3V system, and the PMW signal needs to be input from the two ports (PWM GND) of the terminal.2. When the V/P short contact is disconnected, the 0-5V analog signal input is valid (the default is disconnected at the factory). When the analog quantity is input, the built-in potentiometer on the board can be used to adjust the speed. If you want to connect an external 0 For -5V analog signal input, you must unplug the jumper cap on the board to cut off the potentiometer divider signal, and then input the 0-5V analog signal from the two ports (0-5 GND) of the terminal. The maximum voltage should not exceed 5V3. The forward and reverse rotation and the brake are grounded through a switch, which is low-level effective. The external MCU can also give low-level signals. The front row of wiring terminals are weak current signals directly input to the MCU main control, and cannot be touched or touched. High voltage and strong current.Interface Description:1. U V W 3-phase wire output is connected to brushless motor2. 5V GND The motherboard comes with 5V (current does not exceed 200MA)3. VCC GND main power supply (external DC power supply)4. SC speed pulse signal output (only the interface is reserved, no technical support)5. DIR forward and reverse control keep low level active (can be connected to the ground external switch)6. BRAKE brake control keep low level effective (can be connected to the ground external switch)6. 0-5V PWM speed control signal dual input terminal (on-board potentiometer speed control can also be switched by jumper to connect an external 0-5V analog quantity PWM duty cycle signal input speed control)Parameters:Product name: zs-x11f-2Working voltage: DC 6.5 -50VDrive current: 16A, 30A plus cold air coolingMaximum power: 380WOvercurrent protection: YesLocked-rotor protection: Yes (after locked-rotor, the current will automatically drop and run at intervals)Over-temperature protection: Yes (over-temperature power is halved)Maximum speed: 224000 RPM (2 pole motor), 74000 RPM (6 pole motor), 40000 RPM (12 pole motor), 35000 RPM (14 pole motor).Product size: 63*45*31mmPrecautions:1. Reverse connection of the positive and negative poles of the power supply on the motherboard will cause damage to some chips on the board (even if it is not possible for 1 second)2. There is sampling over-current protection at the output of the motor during normal . Because the power and current of the module are large, please do not artificially short-circuit when the module is not working normally. Once the short-circuit, the circuit may be burnt and the tube may burst. Please test with low current and low voltage. After ok, connect with high current and high voltage. Because it is a bare board module, please pay attention to the insulation of the wiring head. It is strictly forbidden that strong voltage touches the board parts.3. Do not connect the motor that is obviously inconsistent with the drive module voltage, current, or power.Package Included:1 *DC 6.5 -50V Three-Phrase Brushless DC Motor Control Board BLDC Motor Driver Regulator 380W PWM Signal Duty Cycle==========Color : YellowPower Supply : DCModel Number : ZS-X11F V3Motor Type : DC MotorMotor : DC Motor

• Stepper Motor Driver
• 1pc ZS-X11F V3 DC 6.5 -50V Three-Phrase Brushless Motor Control Board BLDC Driver Regulator 380W PWM Signal Duty Cycle